Initial commit.

vpnerator.sh

@@ -0,0 +1,114 @@
+#!/bin/bash
+# Configures a temporary VPN tunnel (using single-use keys) to a remote host
+# using WireGuard: https://www.wireguard.com/
+#
+# Author: Matt Low <matt@mlow.ca>
+#
+
+HOST=$1
+HOST_ADDR=$(echo ${HOST} | awk -F '@' '{ print $NF }')
+
+SERVER_ADDR=10.99.255.1/24
+CLIENT_ADDR=10.99.255.2/32
+DNS=8.8.8.8
+
+echo "Generating keys..."
+SERVER_KEY=$(wg genkey)
+CLIENT_KEY=$(wg genkey)
+SERVER_PUB=$(wg pubkey <<< ${SERVER_KEY})
+CLIENT_PUB=$(wg pubkey <<< ${CLIENT_KEY})
+PSK=$(wg genpsk)
+echo "  Server pubkey: ${SERVER_PUB}"
+echo "  Client pubkey: ${CLIENT_PUB}"
+
+SERVER_SETUP=$(cat << END
+if [ -z "\$(which wg-quick 2>/dev/null)" ]; then
+    echo "wg-quick not found, installing..."
+    sudo apt install -y wireguard-tools 2>/dev/null \
+        || sudo pacman -S --noconfirm wireguard-tools 2>/dev/null \
+        || sudo dnf install -y wireguard-tools iptables 2>/dev/null \
+    [ "\$?" -eq 0 ] || { echo "Could not install wireguard-tools, aborting."; exit 1; }
+fi
+
+sysctl -w net.ipv4.ip_forward=1
+umask 0177
+
+cat << CONF > /tmp/tun.conf
+[Interface]
+Address = ${SERVER_ADDR}
+ListenPort = 51820
+PrivateKey = ${SERVER_KEY}
+PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -A FORWARD -o %i -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
+PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -D FORWARD -o %i -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE
+
+[Peer]
+# foo
+PublicKey = ${CLIENT_PUB}
+PresharedKey = ${PSK}
+AllowedIPs = ${CLIENT_ADDR}
+CONF
+
+sudo wg-quick up /tmp/tun.conf
+END
+)
+
+echo
+echo "Starting server..."
+ssh -T ${HOST} sh <<< "${SERVER_SETUP}" 1>/dev/null
+if [ "$?" -ne 0 ]; then
+    echo "Error starting server, aborting."
+    exit 1
+fi
+
+umask 0177
+cat << CONF > /tmp/tun.conf
+[Interface]
+Address = ${CLIENT_ADDR}
+PrivateKey = ${CLIENT_KEY}
+DNS = ${DNS}
+
+[Peer]
+PublicKey = ${SERVER_PUB}
+PresharedKey = ${PSK}
+Endpoint = ${HOST_ADDR}:51820
+AllowedIPs = 0.0.0.0/0, ::/0
+CONF
+
+echo
+echo "Starting client..."
+sudo wg-quick up /tmp/tun.conf
+
+# clear these variables from memory
+PSK=
+CLIENT_KEY=
+SERVER_KEY=
+
+sleep 1
+echo
+sudo wg show tun
+echo
+echo "Connected! Interrupt or press Enter to disconnect and stop server."
+
+cleanup() {
+	set -e
+	echo
+	echo "Stopping client..."
+	sudo wg-quick down /tmp/tun.conf
+	rm /tmp/tun.conf
+
+	echo
+	echo "Stopping server..."
+	ssh -T ${HOST} <<- END
+	wg-quick down /tmp/tun.conf
+	rm /tmp/tun.conf
+	END
+
+	echo
+	echo "Bye!"
+
+	exit
+}
+
+trap cleanup INT TERM
+read var
+cleanup